来源：创芯大讲堂
创芯大讲堂：EETOP旗下在线教育平台，欢迎关注。
春节期间，EETOP分享了网友通过Vivado直接板级调试时钟用的PCIE IP输出的:春节快乐时序抓取图，纯粹的硬逻辑产生。如下图：
作者：CETC41-缪国锋
实现原理：因为项目需要，需要在板子上完成PCIE接口的通信，还要完成两路AD，两路DA的调试，还有四个颗粒的内存颗粒，来完成信号的收发，FPGA用的是XC7V690T，还有时钟芯片AD9512，ADI的这些芯片多是用SPI来控制寄存器，因此我在写寄存器的时候就想把寄存器的值换成节日祝福，应该挺有新意的，就从新例化了一个module，每配置完一个寄存器自动跳转到下一个，直到所有寄存器配置完成结束，每一个寄存器位数为16位，每个汉字16个值，前后加0隔开，一共74个，时钟也可以根据需要分频更改。
经作者授权，现将实现代码公布给大家：
实现代码包含两个模块：
SPI_16Bit_Controller.v
Spi_Festival_Config.v
SPI_16Bit_Controller.v
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 2019/01/29 09:18:43
// Design Name:
// Module Name: SPI_16Bit_Controller
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module SPI_16Bit_Controller(
input clk_i, //SPI 控制器时钟输入，
input [15:0] spi_data,//SPI 总线时钟信号并行输入
input spi_start,//启动传输
input rst_n,//SPI 控制器复位信号
(* mark_debug = \"true\" *)input spi_miso,//SPI 总线数据信号输入
(* mark_debug = \"true\" *)output wire spi_mosi,//SPI 总线数据信号输出
(* mark_debug = \"true\" *)output wire spi_sclk,//SPI 总线时钟信号输出
(* mark_debug = \"true\" *)output wire spi_cs, //SPI 总线片选信号输出
output reg data_end//传输结束标志
);
//以下信号为测试信号
(* mark_debug = \"true\" *)reg [5:0] sd_counter;//SPI 数据发送计数器
(* mark_debug = \"true\" *)reg spi_sdo_reg;//SPI 控制器发送的串行数据
(* mark_debug = \"true\" *)reg spi_cs_reg;
(* mark_debug = \"true\" *)reg [15:0] spi_data_reg;
assign spi_sclk= (~spi_cs_reg )& ( ((sd_counter >= 2) & (sd_counter <=18))? ~clk_i :0 );
assign spi_mosi =spi_sdo_reg ; //如果输出数据为 1，spi_SDAT 设为高阻
assign spi_cs=spi_cs_reg;
//--SPI 计数器
always @(negedge rst_n or posedge clk_i )
begin
if (!rst_n) sd_counter=6'b000000;
else begin
if (spi_start==0)
sd_counter=0;
else
begin
if (sd_counter == 6'b010011)
sd_counter<=0;
else
sd_counter=sd_counter+1;
end
end
end
always @(negedge rst_n or posedge clk_i )
begin
if (!rst_n)
begin spi_cs_reg=1'b1; spi_sdo_reg=1'b0 ; data_end=1'b1;end
else
case (sd_counter)
6'd0 : begin spi_cs_reg<=1'b1;data_end<=1'b0; spi_sdo_reg=1'b0; end
////////////////////////SPI START////////////////////////////////////
6'd1 : begin spi_cs_reg<=1'b1;spi_data_reg<=spi_data;end
//发送从设备地址
6'd2 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[15]; end
6'd3 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[14]; end
6'd4 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[13]; end
6'd5 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[12]; end
6'd6 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[11]; end
6'd7 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[10]; end
6'd8 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[9]; end
6'd9 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[8]; end
6'd10: begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[7]; end
6'd11 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[6]; end
6'd12 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[5]; end
6'd13 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[4]; end
6'd14 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[3]; end
6'd15 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[2]; end
6'd16 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[1]; end
6'd17 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=spi_data_reg[0]; end
//////////////////////SPI STOP//////////////////////////////////////
6'd18 : begin spi_cs_reg<=1'b0; spi_sdo_reg<=1'b0; data_end<=1'b0 ; end
6'd19 : begin spi_cs_reg<=1'b1; spi_sdo_reg<=1'b0; data_end<=1'b1 ; end
default : begin spi_cs_reg<=1'b1; spi_sdo_reg<=1'b0; data_end<=1'b0 ; end
endcase
end
endmodule
Spi_Festival_Config.v 代码
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 2019/01/29 08:42:10
// Design Name:
// Module Name: Spi_Festival_Config
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Spi_Festival_Config(
input clk_i, //时钟输入
input rst_n, //复位信号
input [12:0] wr_addr,
input [31:0] wr_data,
input wr_en,
input spi_miso, //SPI 总线数据信号输入
output wire spi_sclk, //SPI 总线时钟信号输出
output wire spi_mosi, //SPI 总线数据信号
output wire spi_cs //SPI 使能
);
// 内部寄存器及连线
(* mark_debug = \"true\" *)reg [15:0] spi_data_reg;
(* mark_debug = \"true\" *)reg spi_start;
(* mark_debug = \"true\" *)wire SPI_END; //寄存器并串转换结束标志位
(* mark_debug = \"true\" *)reg [15:0] reg_data;
(* mark_debug = \"true\" *)reg [7:0] addr_index;
//时钟参数
parameter CLK_Freq = 100000000; //输入的系统时钟 100MHz
parameter SPI_Freq = 50000000; //SPI 总线时钟 10MHz
//存储SPI配置数据的查找表容量
parameter LUT_SIZE = 72;
(* mark_debug = \"true\" *)reg [1:0] state;
//state machine code
localparam S_IDLE = 2'b00;
localparam S_START = 2'b01; //start bit
localparam S_STOP = 2'b10;
//////100MHz 时钟分频得到 10MHz 的 SPI 控制时钟//////
(* mark_debug = \"true\" *)reg [7:0] spi_clk_div;
(* mark_debug = \"true\" *)reg spi_ctrl_clk;
always@(posedge clk_i or negedge rst_n)
begin
if(!rst_n)
begin
spi_ctrl_clk <= 0;
spi_clk_div <= 8'h00;
end
else
begin
if( spi_clk_div ==(CLK_Freq/SPI_Freq-1'b1))
begin
spi_clk_div <= 0;
spi_ctrl_clk <= ~spi_ctrl_clk;
end
else
spi_clk_div <= spi_clk_div+1;
end
end
wire initial_en; //触发信号,可使用单脉冲做触发源；
reg initial_clr; //初始化结束清零位；
reg wr_start_en; //初始化使能开始；
assign initial_en=(wr_addr==12'h660 & wr_en);
always@(posedge clk_i)
begin
if(initial_clr)
begin
wr_start_en<=1'b0;
end
else if(initial_en)
begin
wr_start_en<=1'b1;
end
end
////////////////////// 配置过程控制 ///////////////////////
always@(posedge spi_ctrl_clk or negedge rst_n)
begin
if(~rst_n) //复位
begin
addr_index <= 0;
spi_start <= 0;
end
else
begin
if (wr_start_en)
begin
if(addr_index<LUT_SIZE)
begin
case(state)
S_IDLE: begin //第一步：准备数据，启动传输
spi_data_reg <= reg_data;
spi_start <= 1'b1;
state <= 1'b1;end
S_START:
begin
if(SPI_END) //第二步：检验传输是否正常结束
begin
state <= S_STOP;
spi_start <= 1'b0;
end
else
state <= S_START;
end
S_STOP: begin //传输结束，改变 LUT_INDEX 的值，准备传输下一个数据
addr_index <= addr_index+1;
state <= S_IDLE;end
endcase
end
else
begin
state <= S_IDLE;
addr_index<=0;
initial_clr<=1'b1;
end
end
else initial_clr<=1'b0;
end
end
///////////////////// 配置数据查找表 //////////////////////////
always @(posedge clk_i )
begin
case(addr_index)
8'd00 : begin reg_data <= 16'h0000; end
8'd01 : begin reg_data <= 16'h0000; end
8'd02 : begin reg_data <= 16'h0020; end
8'd03 : begin reg_data <= 16'h0020; end
8'd04 : begin reg_data <= 16'h0040; end
8'd05 : begin reg_data <= 16'h1140; end
8'd06 : begin reg_data <= 16'h1180; end
8'd07 : begin reg_data <= 16'h15ff; end
8'd08 : begin reg_data <= 16'h1549; end
8'd09 : begin reg_data <= 16'h7f49; end
8'd10 : begin reg_data <= 16'h7f49; end
8'd11 : begin reg_data <= 16'h1549; end
8'd12 : begin reg_data <= 16'h15ff; end
8'd13 : begin reg_data <= 16'h1180; end
8'd14 : begin reg_data <= 16'h1140; end
8'd15 : begin reg_data <= 16'h0040; end
8'd16 : begin reg_data <= 16'h0020; end
8'd17 : begin reg_data <= 16'h0020; end
8'd18 : begin reg_data <= 16'h0000; end
8'd19 : begin reg_data <= 16'h0000; end
8'd20 : begin reg_data <= 16'h0800; end
8'd21 : begin reg_data <= 16'h0800; end
8'd22 : begin reg_data <= 16'h0900; end
8'd23 : begin reg_data <= 16'h0900; end
8'd24 : begin reg_data <= 16'h7f00; end
8'd25 : begin reg_data <= 16'h7f00; end
8'd26 : begin reg_data <= 16'h0900; end
8'd27 : begin reg_data <= 16'h09ff; end
8'd28 : begin reg_data <= 16'h09ff; end
8'd29 : begin reg_data <= 16'h0900; end
8'd30 : begin reg_data <= 16'h7f20; end
8'd31 : begin reg_data <= 16'h7f20; end
8'd32 : begin reg_data <= 16'h0910; end
8'd33 : begin reg_data <= 16'h09f0; end
8'd34 : begin reg_data <= 16'h0800; end
8'd35 : begin reg_data <= 16'h0800; end
8'd36 : begin reg_data <= 16'h0000; end
8'd37 : begin reg_data <= 16'h0000; end
8'd38 : begin reg_data <= 16'h0180; end
8'd39 : begin reg_data <= 16'h0e00; end
8'd40 : begin reg_data <= 16'h7fff; end
8'd41 : begin reg_data <= 16'h7fff; end
8'd42 : begin reg_data <= 16'h0c00; end
8'd43 : begin reg_data <= 16'h0443; end
8'd44 : begin reg_data <= 16'h0842; end
8'd45 : begin reg_data <= 16'h084c; end
8'd46 : begin reg_data <= 16'h0858; end
8'd47 : begin reg_data <= 16'h7fe0; end
8'd48 : begin reg_data <= 16'h0870; end
8'd49 : begin reg_data <= 16'h084c; end
8'd50 : begin reg_data <= 16'h0846; end
8'd51 : begin reg_data <= 16'h0fc2; end
8'd52 : begin reg_data <= 16'h0041; end
8'd53 : begin reg_data <= 16'h0040; end
8'd54 : begin reg_data <= 16'h0000; end
8'd55 : begin reg_data <= 16'h0000; end
8'd56 : begin reg_data <= 16'h0006; end
8'd57 : begin reg_data <= 16'h3f8c; end
8'd58 : begin reg_data <= 16'h2098; end
8'd59 : begin reg_data <= 16'h20b0; end
8'd60 : begin reg_data <= 16'h2081; end
8'd61 : begin reg_data <= 16'h2081; end
8'd62 : begin reg_data <= 16'h2083; end
8'd63 : begin reg_data <= 16'h2ffe; end
8'd64 : begin reg_data <= 16'h2080; end
8'd65 : begin reg_data <= 16'h4080; end
8'd66 : begin reg_data <= 16'h4080; end
8'd67 : begin reg_data <= 16'h4098; end
8'd68 : begin reg_data <= 16'h408c; end
8'd69 : begin reg_data <= 16'h4086; end
8'd70 : begin reg_data <= 16'h0000; end
8'd71 : begin reg_data <= 16'h0000; end
default: begin reg_data <= 16'h0000; end
endcase
end
// 定义上位机单独配置寄存器的值，无需更改不用配置
reg pci_write_en;
reg [15:0] spi_data;
reg [7:0] wr_en_cnt;
always@(posedge clk_i)
begin
if(SPI_END)
begin
pci_write_en<=1'b0;
end
else if(wr_addr==12'h650 & wr_en)
pci_write_en<=1'b1;
end
always@(posedge clk_i)
begin
if(~rst_n)
spi_data<=16'h0000;
else
begin
if((wr_addr[12:0]==13'h640) & wr_en)
spi_data<=wr_data[15:0];
else if(spi_start)
spi_data<=spi_data_reg[15:0];
end
end
wire spi_en;
assign spi_en=pci_write_en | spi_start;
////例化 SPI 控制器 将16位并行数据完成并串转换///
SPI_16Bit_Controller SPI_16Bit_Controller_inst(
.clk_i (spi_ctrl_clk), // SPI 控制器工作时钟
.spi_sclk , // SPI 总线时钟信号
.spi_miso , // SPI 总线数据信号
.spi_mosi , // SPI 总线数据信号
.spi_cs , // SPI 总线使能信号
.spi_data (spi_data), //寄存器data
.spi_start (spi_en), // 启动传输
.data_end (SPI_END), // 传输结束标志
.rst_n (rst_n) //复位信号
);
endmodule
